Icon THE LAB
The Lab Report · Structure Series

Rigid Box Board Thickness & Magnet Strength:
What to Specify Before You Quote

Thickness decides how the box feels in hand; magnets decide how it holds. Fix thickness first from the box footprint and product weight — then size the magnets to the lid area that thickness gives you.

This page exists for the buyer who has to write the specification rather than approve one. Two parameters decide most of what the customer feels when the lid comes off — greyboard thickness and magnet placement — and both are locked before the print run. Get them into the brief in the right order and the sample review becomes a confirmation instead of a negotiation.

Board Thickness Sets the Weight in Hand

Greyboard is the core of every custom magnetic rigid boxes build, and its grade is the first decision on the sheet. Our published band runs 900, 1000, 1200, 1500 and 2000 gsm. The band is not a ladder where more is automatically better — it is matched against three things: product weight, box footprint, and how much the lid has to resist bowing.

The failure mode to design against is a thin board over a wide face. A large lid in light board flexes under its own span, the lid edge stops meeting the base cleanly, and the box gives itself away before anyone notices the print. That is why the footprint often decides the grade before the product weight does: a heavy product in a small box is easier to specify than a light product in a wide one. Depth matters too — a deep base in thin board loses its vertical stiffness and the walls start to flare.

One practical note on how thickness behaves in the hand: the step from 900 to 1200 gsm is felt immediately, while the step from 1500 to 2000 gsm reads more in rigidity and lid behaviour than in raw weight. If a brief asks for "heavy, premium board" without a size, the honest answer is that size has to come first — the grade is a function, not a preference.

Magnet Grade, Count and Pocket Depth

The hold a customer feels is the product of four variables, not one: magnet grade, diameter, thickness, and how deep the pocket sits inside the board. Change any one of them and the click changes. This is the sentence that explains why a magnetic closure cannot be specified from a catalogue line — a grade that feels right in a small rigid box will feel wrong in a wide one, not because it is weaker but because the lid it is pulling is larger.

On grade, the industry references published neodymium grades — N35 through N52 — as a shared vocabulary for the material itself. What matters for a box is not the number but the selection: grade is chosen against the box, the wrap thickness and the opening action you want, then proven rather than assumed. We do not publish a pull figure for a finished box, and we would treat one with suspicion if a supplier did: the number a datasheet quotes is measured on a bare magnet, while the number your customer feels is measured through board, wrap and pocket depth.

Count and position are the other half. More magnets do not automatically mean a better closure — they mean more pockets, more hand operations and, past a point, a lid that fights the customer on opening. The target is a lid that stays closed through handling and opens with one hand when asked. That is a balance, and it is the reason pocket position is driven by the drawing: a re-order should feel like the first run, not like a cousin of it.

Pocket Tolerance Is the Whole Game

If one sentence from this page survives into your brief, make it this one: pocket position is a dimensional tolerance question, not a decoration question. Pockets set by eye produce a lid that drifts instead of snapping — the box still closes, but the alignment is soft and the customer feels it before they can name it.

In a magnetic rigid gift boxes build the magnets are set inside the greyboard layers and covered by the wrap, so pocket depth carries two jobs at once: it sets the distance between the magnet pairs, and it keeps the magnet invisible. Too shallow telegraphs through the paper; too deep softens the hold. Both ends of that range are visible in the finished box, which is why the depth is controlled on the drawing rather than adjusted on the bench.

Hidden integration is also what makes re-orders predictable. Because the wrap is applied over the assembled board, the closure is never re-tuned after finishing — the positions were fixed earlier, in the flat. A second run from the same drawing feels like the first; a second run from a photograph does not.

Wrap and Moisture: The Quiet Failure

The most common defect in a wrapped rigid box is not structural at all — it is the surface lifting days after delivery. Board and face paper carry different moisture content, and wrapping them at different conditions leaves that difference inside the finished panel. The surface then moves as it equalises. Lamination does not fix this; it hides it for a week and then follows the same path.

The right control is upstream: board is conditioned before wrapping so that board and paper are close enough in moisture that neither has to move. This is the same discipline that runs through the whole finishing stack — when a surface treatment is chosen to solve a conditioning problem, it usually becomes a second problem. The options and their trade-offs are documented separately in the Material & Finishing Lab.

Condition the board before you wrap it. Everything else about a rigid box surface is easier after that.

Eight Lines You Can Paste Into Your Brief

Most quote cycles lose a week to missing parameters. These eight lines cover what a supplier needs to price a rigid box without guessing — paste them into your brief, fill what you know, and leave the rest to be resolved on the sample.

Parameter What to give us Example
Outside dimensions Length × width × depth, in mm — the die is cut from this line 220 × 160 × 70 mm
Board grade Greyboard gsm band for the lid and the base 1200 gsm lid / 1000 gsm base
Magnet grade & count Published grade reference and how many per closure N35, 4 per box
Pocket position Set from the drawing — face, depth and inset from the edge 2 per side, 12 mm inset
Wrap paper Face paper and its weight; textured or plain 128 gsm art paper, matte
Surface finishing Lamination, spot UV, foil — inside and outside Matte lam outside, foil inside
Order quantity Units per size, and whether re-orders are expected 500 units, annual re-order
Delivery basis DDP or EXW, and the destination market DDP to US

The example column shows the form of an answer, not a recommendation — the values come from your product

With those eight lines, the return is a specification rather than a catalogue price, and the sample review becomes a confirmation of pocket depth and hand feel. Everything upstream of that — how thickness and magnet placement interact across the published grade band — sits on the magnetic rigid gift boxes hub page.

Board Thickness & Magnet Strength, Answered

What thickness greyboard should a gift box use? +

It follows the box footprint and the product weight, not a house default. Our published band runs 900 to 2000 gsm: thinner board suits small, light boxes, while a wide face or a heavy product wants the upper end, because thin board over a large face is where a rigid box reads as cheap. Give us the outside dimensions and the product weight and the band narrows to one or two candidates.

How strong should the magnets be? +

Strong enough to hold the lid closed through handling, and no more. Pull is the product of four variables rather than one — grade, diameter, thickness and pocket depth — so it is selected against the box, not bought off a shelf. We quote the variables and confirm the feel on a working sample; we do not publish a pull figure, because the number on a datasheet is not the number your customer feels through a wrap.

Do the magnets show through the wrap? +

No. The magnets are set inside the greyboard layers and then covered by the wrap, so from the outside the closure is felt rather than seen. Pocket depth is what keeps it invisible — set too shallow and the magnet telegraphs through the paper as a faint circle under raking light. This is checked on the sample, on the actual wrap, not on a bare board.

Will the lid loosen over time? +

It can, and the pocket is where it happens first. A pocket that was set slightly deep lets the magnets sit further apart, which reads as a softer hold over repeated openings. Pocket depth is therefore controlled from the drawing and repeated on re-orders. If a box is going into long-term reuse rather than one delivery, say so when you brief us — that changes the specification.

Can I change the magnets after sampling? +

You can, and it is cheaper to do it at sample stage than after the die is cut. Changing grade, diameter or count means re-setting pocket positions, which is a die and plate change rather than a material swap. Bring every magnet question to the sample review and lock it before the print run — after that, the positions are part of the tooling.

The Lab Report

BrandPackagingLab — Lab Engineering Desk. Engineering notes on premium packaging, tested against real buyer behaviour.

Greyboard grades per published structure specs · neodymium grades referenced as industry-standard material classes (N35–N52) · closure behaviour confirmed on the working sample