Paper Bag Paper Stock:
How GSM, Kraft and Specialty Paper Change the Bag
The weight ladder is not a quality ladder. Above 280 gsm the sheet carries more fibre and resists bursting better — but that same mass moves the failure to the crease, and on coated stock the crease is exactly where the coating fractures. Below 250 gsm, within the same stock family, the bag loses mouth crispness and edge sharpness. 250 gsm is where burst margin, crease quality and handling rigidity overlap for most retail bags — and it is the heaviest weight we hold as standard across both coated and uncoated lines. 280 and 300 gsm sit above it, where the sheet behaves as a heavier board and the crease becomes the controlling risk.
Three numbers that get used as one
Buyers quote a bag by weight because weight is the only number on the spec sheet. But three different properties decide how the bag behaves in a customer's hand:
- GSM — grams per square metre. The mill's number for the sheet.
- Caliper (bulk) — how thick the sheet actually is. Coating and calendering compress the fibre, so a heavily coated sheet can be thinner than an uncoated one at equal GSM.
- Stiffness — how the sheet resists bending. This is what a buyer is really asking for when they say "a sturdier bag".
The practical consequence: coating buys you print quality and costs you bulk. Uncoated kraft at the same weight usually reads firmer and more matte, and takes ink differently. Neither is better. They fail in different places.
The published grades and surface options behind all of this are set out on custom paper bags.
The four stocks we tool
Coated art paper. The print surface. Holds four-colour process, spot colour, foil and blind deboss with the highest fidelity of the four. It is also the sheet most likely to crack along a hard fold line, because the coating is a film sitting on top of the fibre — which is why deep folds on coated stock need a crease, not a score-and-hope.
Coated card / white card. Same printing logic as art paper with more body. Used where the bag needs to hold a squared-open mouth rather than collapse. Colour reads consistent across a run, which matters on large solid areas.
Uncoated kraft. Long virgin fibre, no coating film. Ink sits into the sheet rather than on it, so process colour shifts warmer and fine reversed type fills in. It prints single- and two-colour marks cleanly, and it keeps the recycling stream simple because there is no laminate to separate. Its limitation is resolution, not strength.
Specialty textured paper. Bought for hand-feel: embossed, felt and linen surfaces are the common market categories. The texture is the product. It also sets three constraints covered below.
Which of the four is held in which grade is the substance of the custom printed paper bags specification.
The weight ladder: where the trade-off actually sits
We tool four weights — 230, 250, 280 and 300 gsm — and the step between them is not linear in feel. 230 and 250 are held as standard stock across both coated and uncoated lines; 280 and 300 are quoted per order. Three bands do different jobs:
| Band | What it does | Where it fails | Use it for |
|---|---|---|---|
| Below 250 gsm | Lighter sheet, less fibre mass, folds cleanly | Mouth loses crispness, edge reads soft | Light retail, takeaway, single-colour marks |
| 250 gsm | The overlap point: burst margin, crease quality and handling rigidity hold together | Nothing dramatic — it is the compromise, not the peak | Default for most retail bags |
| 280 gsm and above | Most fibre mass; best resistance to bursting through the panel | The crease becomes the weakest line; coated stock fractures at the fold | Heavy or gift loads, bags that must stand open |
Grades per published structure specs · 230 and 250 gsm held as standard stock, 280 and 300 gsm quoted per order
Moving up a step changes four things at once:
- Crease behaviour. Heavier coated sheets need a proper crease line or the coating fractures at the fold.
- Handle anchoring. A ribbon, bow or webbing handle loads the top edge; the sheet has to carry that anchor without the reinforcement showing through the face.
- Mouth behaviour. Whether the bag stays open on a counter or folds flat in a shelf stack.
- Freight weight. Heavier stock means more kilos per carton, which shows up in freight and, in the EU, in packaging-weight-based fees.
What does not change predictably is load. Stiffness depends on fibre, bulk and construction together, so a load figure belongs to a proven working sample of your bag, not to a GSM number on a page.
Grade and size are decided together, because a larger panel flexes more at the same grade. The measurement half of that decision — H × L × W and the gusset — is in the paper bag size guide.
Specialty paper: three real costs
- Print. Texture breaks up fine type and small reversed logos. Large solid process areas print unevenly because the surface absorbs at different rates across the pattern. Specialty stock is usually the right answer for a foil mark, a deboss or a single-colour logo — and the wrong answer for a photographic four-colour panel.
- Fold. Texture has a direction. Folded against the grain it lifts and can split along the pattern; folded with it, it creases cleanly. Grain direction has to be agreed at artwork stage, not discovered at delivery.
- Finishing. Lamination needs a flat surface; on texture it either bridges the pattern or fails to bond. Foil adhesion varies by pattern depth. Both are testable on a sample, neither is guessable from a swatch.
A selection matrix
| What the bag has to do | Stock | Weight band |
|---|---|---|
| Retail counter, heavy print, brand-led | Coated art paper | Mid to upper ladder |
| Gift and event, squared-open mouth | Coated card | Upper ladder |
| Grocery, takeaway, single-colour mark | Uncoated kraft | Lower to mid ladder |
| Specialty retail where hand-feel is the point | Specialty textured | Mid ladder, finishing tested first |
| High-volume reorder, consistent colour | Coated card | Mid ladder |
The matrix is a starting point, not a verdict: it tells you which stock family a job belongs to and roughly where on the ladder to begin sampling. The structures themselves — the bag shapes these stocks are built into — are on the luxury paper bags page.
Four mistakes worth avoiding
- Choosing by GSM alone. The number is comparable only within the same stock family.
- Deep-folding coated stock without a crease. The failure appears as a white line at the fold, after printing.
- Running four-colour process on textured stock. It is possible; it is rarely what the buyer expected.
- Reading FSC as recyclable. FSC tells you where the fibre came from. It says nothing about whether the finished bag — coating, laminate, handle — goes into the paper stream. Those are separate claims and must be written separately.
Paper Bag Materials, Answered
What GSM is a paper bag? +
There is no single industry weight. Retail bags are specified across a range, and the number only means something alongside the stock family, the bag size and the handle type.
Why does a heavier bag crack at the fold? +
Because the fold is where the sheet is asked to do two things at once: compress on the inside of the crease and stretch on the outside. On coated stock the coating is a film on the surface and cannot stretch with the fibre, so it fractures. A crease line, cut before folding, spreads that strain.
Is thicker paper always stronger? +
No. Stiffness comes from fibre, bulk and construction. Thickness alone does not predict how a loaded bag behaves.
Can I print full colour on textured paper? +
You can print on it; the texture will show through the ink and fine detail will close up. Foil, deboss and solid single colour hold up far better.
Two ways forward
The Lab Report
Written by Aron Lew, Lab Engineering Desk. Stock weights, surface options and lead times quoted here follow our published capability data.
Reviewed 4 November 2026 against published mill and plant specifications · regulatory statements reflect rules in force at that date and should be re-checked before you rely on them